Slurry Parts for Sale (All prices exclude VAT)
Slurry Store Bolts
I stock large quantities of the special bolts used in slurry stores. Order below, or see www.silobolts.co.uk for more information
I stock large quantities of the special bolts used in slurry stores. Order below, or see www.silobolts.co.uk for more information
These bolts are ½" UNC thread, galvanised with a plastic cap for additional protection from corrosion, and are made in lengths from 1" up to 2", in ¼" increments and also 2½"; 3" bolts are also available, however these are fully threaded, like set screws.
Nut caps, if required, can be supplied.
Nut caps, if required, can be supplied.
Sikaflex TS+ mastic for tanks and silos.
(TS stands for Tank Specification).
Approved for contact with drinking water
(TS stands for Tank Specification).
Approved for contact with drinking water
Prices:
1” slurry store bolts black cap £294.00 per thousand £0.35 ea if order is below 250
1 ¼” slurry store bolts grey cap £306.00 per thousand £0.38 ea if order is below 250
1 ½” slurry store bolts blue cap £372.00 per thousand £0.44 ea if order is below 250
1 ¾” slurry store bolts white cap £385.00 per thousand £0.48 ea if order is below 250
2” slurry store bolts red cap £438.00 per thousand £0.52 ea if order is below 250
2½" slurry store bolts tan cap £486.00 per thousand £0.58 ea if order is below 250
3" slurry store bolts yellow cap £552.00 per thousand £0.66 ea if order is below 250
Galvanised ½” UNC nuts £48.00 per thousand £0.06 ea unless ordered with 250 bolts
All nuts are grade 10, and tapped 10 thou oversize.
Washers £26.50 per thousand £0.04 ea unless ordered with 250 bolts
Plastic nut caps £110.00 per thousand £0.15 ea
Sika TS+ mastic (600cc sausages) £231.00 per box of 20 £13.20 ea
NB. Nuts, bolts and washers are sold separately. These prices exclude carriage and packing and are +VAT
Export orders welcome.
Either use the contact form below or email [email protected] for a quote and to place an order.
1” slurry store bolts black cap £294.00 per thousand £0.35 ea if order is below 250
1 ¼” slurry store bolts grey cap £306.00 per thousand £0.38 ea if order is below 250
1 ½” slurry store bolts blue cap £372.00 per thousand £0.44 ea if order is below 250
1 ¾” slurry store bolts white cap £385.00 per thousand £0.48 ea if order is below 250
2” slurry store bolts red cap £438.00 per thousand £0.52 ea if order is below 250
2½" slurry store bolts tan cap £486.00 per thousand £0.58 ea if order is below 250
3" slurry store bolts yellow cap £552.00 per thousand £0.66 ea if order is below 250
Galvanised ½” UNC nuts £48.00 per thousand £0.06 ea unless ordered with 250 bolts
All nuts are grade 10, and tapped 10 thou oversize.
Washers £26.50 per thousand £0.04 ea unless ordered with 250 bolts
Plastic nut caps £110.00 per thousand £0.15 ea
Sika TS+ mastic (600cc sausages) £231.00 per box of 20 £13.20 ea
NB. Nuts, bolts and washers are sold separately. These prices exclude carriage and packing and are +VAT
Export orders welcome.
Either use the contact form below or email [email protected] for a quote and to place an order.
Rag Bolts
(Indented Foundation bolts)
These are pushed into wet concrete and the nuts are tightened up on to clamps which hold the tank down to the ring beam.
M16 and M 20 are both used for slurry stores.
Some old stock M16 x275 at reduced price. £5.00 each.
Also new hot dip galvanised, M16 x 275 ……£14.20 each, M20 x 275…….£15.40 each
M16 and M 20 are both used for slurry stores.
Some old stock M16 x275 at reduced price. £5.00 each.
Also new hot dip galvanised, M16 x 275 ……£14.20 each, M20 x 275…….£15.40 each
Holding down clamps for slurry stores.
New and used, to fit M16 or M20 Rag bolts. A few extended clamps for when the rag bolt has not been positioned correctly.
Price: open to offers, guide £5.00 each
New and used, to fit M16 or M20 Rag bolts. A few extended clamps for when the rag bolt has not been positioned correctly.
Price: open to offers, guide £5.00 each
Pease continue scrolling down past the contact form for more items for sale.
Brass (MZ type) slurry valves
|
|
Handles for the above valves
4", 5", 6"....... £20.32
8"..................£34.24
Repair parts for Harvestore type slurry sluice valves
In stainless steel to overcome the problem of corrosion around the operating rod.
In stainless steel to overcome the problem of corrosion around the operating rod.
|
SLIDE complete with washer plates and rubber cushion washers.......................................................................................... £300.00
3/4" UNC stainess locking half nuts.......................................£2.50 each Operating rod, threaded each end...............................................£55.00 Galvanised clevis, threaded to fit the rod, c/w bolt and locking nut......................................................................................................£21.00 Soft rubber face seal that the slide is pushed against by the presssure of the slurry........................................................................................£87.00 Gland seal, prevents slurry leaking round the operating rod.......................................................................................................£14.50 Other parts available, either re-conditioned or new, please ask. |
|
|
Replacement double sluice gate.
Some older Harestore/A O Smith stores used a pair of 12" valves coupled together in the reception pit. Often now beyond repair, the cheapest solution is an adaptor flange and two 8" or similiar valves bolted together. POA.
I strongly suggest that somebody with all safety equipment works in a reception pit; walking around in the slurry can release highly poisonous gases.
I strongly suggest that somebody with all safety equipment works in a reception pit; walking around in the slurry can release highly poisonous gases.
Suction Hose.
3", 4", 5", 6" Medusa Super Elastic, blue and grey. In stock, sold by the metre. 8" also available to order.
2" green also in stock, useful for delivery from submersible pimps. Please phone or email for prices.
8" suction hose is normally only sold in 6.0 metre lengths.
2" green also in stock, useful for delivery from submersible pimps. Please phone or email for prices.
8" suction hose is normally only sold in 6.0 metre lengths.
Old Stock Layflat Hose (not suitable for dragging/umbilical)
Blue, 5" ID (127mm), 6 bar rating. Red, 6" ID (152mm), 6 bar rating. Very cheap, only £7.50/ metre, either size.
I have succesfullly used this when there have been complaints about smell when pumping into a store through a jetter. A length of layflat long enough to reach well down into the tank will reduce spray into the air, while not allowing the slurry to siphon back. A belt and braces approach would fit a non-return valve above the pump, or even a gate valve, but this should not be necessary.
I have succesfullly used this when there have been complaints about smell when pumping into a store through a jetter. A length of layflat long enough to reach well down into the tank will reduce spray into the air, while not allowing the slurry to siphon back. A belt and braces approach would fit a non-return valve above the pump, or even a gate valve, but this should not be necessary.
Hose Clips (Bolt Pattern) in Stainless. Also in cheaper BZP.
I carry a full range of sizes suitable for 2" layflat through to 6" suction hose. Please ask for prices.
For guidance, 113-120 mm should fit 4" suction hose, 131-139mm should fit 5" sucton hose, and 162-174mm should fit 6".
For guidance, 113-120 mm should fit 4" suction hose, 131-139mm should fit 5" sucton hose, and 162-174mm should fit 6".
Hose Tails and Bauer Couplings. A Wide Range.
I stock or can supply most Bauer type couplings in all sizes. As well as hose tails, I have a few Bauer/BSP thread fittings in stock, bends and reducers or expanders. I can supply replacement rubber sealing rings to fit female Bauer couplings.
Please ask for prices
Please ask for prices
Various MZ Flanged Galvanised Fittings
I have various galvanised fittings, flanged to fit 4-hole MZ type slurry fittings and brass valves. These include tank outlet flanges,medium and heavy duty, drilled to use slurry tank bolts. The 1.0metre straight pipe and Tee have had light use.
Most parts are 6" but some 8".
Price: open to sensible offers.
Most parts are 6" but some 8".
Price: open to sensible offers.
3" BSP Threaded Parts
Over the years I have amassed a few 3" BSP threaded galvanised parts.
Guide prices for your offers shown below.
Strainer -OD 150mm, with 8mm diameter holes. £20.00
Flange 8 off 18 mm holes on160mm PCDmaking it PN 10/16 £20.00
Sockets £4.00
Pipe nipples: 60mm long £2.50; 100mm long £4.00; 200mm long £8.00; 250mm long £10.00; 300mm long £10.00.
I also have a few other size threaded parts, some used, at clearance prices. Please ask.
Guide prices for your offers shown below.
Strainer -OD 150mm, with 8mm diameter holes. £20.00
Flange 8 off 18 mm holes on160mm PCDmaking it PN 10/16 £20.00
Sockets £4.00
Pipe nipples: 60mm long £2.50; 100mm long £4.00; 200mm long £8.00; 250mm long £10.00; 300mm long £10.00.
I also have a few other size threaded parts, some used, at clearance prices. Please ask.
45 Degree Weld Elbow 8" Nominal Bore.
Clearance price: £10.00 only, probably less than scrap price!
Various Loose Flanges, mostly galvanised and used previously.
|
|
|
|
|
|
I hope the dimensios are self-explanatory; any questions, email [email protected] Price: only £2.00 each, the pair which includes the flange threaded M12, and backing flange, £4.00. Open to offers.
Catwalk. Actually off a 15'/18'6"diameter silo.
Will be supplied complete with handrails and stop-ends, brackets, galvanised bolts and nuts, to use similar to the shiny one in the pictures. Any body with an old Boythorpe silo will have struggled with the roof ladder in the second picture. This will be easier to use and much safer. Or use it for something else?
As shown, including handrails etc. £250.00 or re- galvanised + cost of galvanising.
Fixed ladder sections.
The following lengths: 33"; 54"; 63.5"; 67.75" Safety cage and choice of fixing brackets can be included for no extra cost.
Slurry Store Outlets.
All parts are usually in stock, both 6" and 8". The example shown was loosely assembled for demonstration purposes.
I have found that if the parts inside the store are galvanized steel, they will rust surprisingly quickly, particularly if the store is emptied regularly! As a result I have managed to get the flanges made in PVC and any pipe work, 160mm (6") or 225mm (8"). This can be assembled so that it dips into the original outlet for better emptying.
Prices, supplied and fitted from £2500.00 + VAT.
Once again I must stress that it is not safe to go into a slurry store without carrying a gas alarm.
I have found that if the parts inside the store are galvanized steel, they will rust surprisingly quickly, particularly if the store is emptied regularly! As a result I have managed to get the flanges made in PVC and any pipe work, 160mm (6") or 225mm (8"). This can be assembled so that it dips into the original outlet for better emptying.
Prices, supplied and fitted from £2500.00 + VAT.
Once again I must stress that it is not safe to go into a slurry store without carrying a gas alarm.
